Part Number: AA4040SGS Super Bright Green Features zSingle color. zSuitable for all SMT assembly and solder process. zAvailable on tape and reel. zIdeal for backlighting. zPackage : 500pcs / reel. zMoisture sensitivity level : level 3. zRoHS compliant. Description The Super Bright Green source color devices are made with Gallium Phosphide Green Light Emitting Diode. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.25(0.01\") unless otherwise noted. 3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAL0975 REV NO: V.2 DATE: APR/01/2011 PAGE: 1 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: J.Yu ERP: 1201006832
芯天下--http://oneic.com/
Handling Precautions Compare to epoxy encapsulant that is hard and brittle, silicone is softer and flexible. Although its characteristic significantly reduces thermal stress, it is more susceptible to damage by external mechanical force. As a result, special handling precautions need to be observed during assembly using silicone encapsulated LED products. Failure to comply might lead to damage and premature failure of the LED. 1. Handle the component along the side surfaces by using forceps or appropriate tools. 2. Do not directly touch or handle the silicone lens surface. It may damage the internal circuitry. 3. As silicone encapsulation is permeable to gases, some corrosive substances such as H2S might corrode silver plating of leadframe. Special care should be taken if an LED with silicone encapsulation is to be used near such substances. SPEC NO: DSAL0975 REV NO: V.2 DATE: APR/01/2011 PAGE: 2 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: J.Yu ERP: 1201006832
芯天下--http://oneic.com/
Selection Guide
Part No.
Dice
Lens Type
Viewing Iv (mcd) [2] @ 20mA Angle [1] Min.
Typ. 30
2θ1/2 120°
AA4040SGS Super Bright Green (GaP) Water Clear 15
Notes:
1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity/ luminous Flux: +/-15%.
Electrical / Optical Characteristics at TA=25°C
Symbol λpeak λD [1] Δλ1/2 C VF [2] IR
Parameter Peak Wavelength Dominant Wavelength Spectral Line Half-width
Capacitance Forward Voltage Reverse Current
Device Super Bright Green Super Bright Green Super Bright Green Super Bright Green Super Bright Green Super Bright Green
Typ. 565 568 30 15 2.2
Max. 2.5 10
Units nm nm nm pF V uA
Test Conditions
IF=20mA IF=20mA IF=20mA VF=0V;f=1MHz IF=20mA VR=5V
Notes:
1.Wavelength: +/-1nm.
2. Forward Voltage: +/-0.1V.
Absolute Maximum Ratings at TA=25°C
Parameter Power dissipation DC Forward Current Peak Forward Current [1] Reverse Voltage Operating Temperature Storage Temperature
Note:
1. 1/10 Duty Cycle, 0.1ms Pulse Width.
Super Bright Green
62.5 25 140 5
-40°C To +85°C -40°C To +85°C
Units mW mA mA V
SPEC NO: DSAL0975 REV NO: V.2 DATE: APR/01/2011 PAGE: 3 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: J.Yu ERP: 1201006832
芯天下--http://oneic.com/
Super Bright Green AA4040SGS SPEC NO: DSAL0975 REV NO: V.2 DATE: APR/01/2011 PAGE: 4 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: J.Yu ERP: 1201006832
芯天下--http://oneic.com/
AA4040SGS Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Reel Dimension Tape Dimensions (Units : mm) SPEC NO: DSAL0975 REV NO: V.2 DATE: APR/01/2011 PAGE: 5 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: J.Yu ERP: 1201006832
芯天下--http://oneic.com/
PACKING & LABEL SPECIFICATIONS AA4040SGS SPEC NO: DSAL0975 REV NO: V.2 DATE: APR/01/2011 PAGE: 6 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: J.Yu ERP: 1201006832
芯天下--http://oneic.com/
因篇幅问题不能全部显示,请点此查看更多更全内容
Copyright © 2019- dfix.cn 版权所有 湘ICP备2024080961号-1
违法及侵权请联系:TEL:199 1889 7713 E-MAIL:2724546146@qq.com
本站由北京市万商天勤律师事务所王兴未律师提供法律服务