OP165A,OP166A,OP165D,OP165C,OP165B,OP166D,OP165W,OP166C, 规格书,Datasheet 资料

OP165, OP166 Series

Features: • T-1 (3 mm) package style • Choice of narrow or wide irradiance pattern • Choice of dome lens or flat lens • Mechanically and spectrally matched to other OPTEK devices • Higher power output than GaAs at equivalent drive currents • 935 nm diode Description:

Each device in the OP165 and OP166 series is a high intensity gallium arsenide infrared emitting diode (GaAIAs) that is molded in an IR transmissive clear epoxy package with either a dome or flat lens. Devices feature narrow and wide irradiance patterns and a variety of electrical characteristics. The small T-1 package style makes these devices ideal for space-limited applications.

OP165 and OP166 devices are mechanically and spectrally matched to the OP505 and OP535 series devices.

Please refer to Application Bulletins 208 and 210 for additional design information and reliability (degradation) data. Applications:

• Space-limited applications • Applications requiring coupling

Part Number OP165A OP165B OP165C OP165D OP165W OP166A OP166B OP166C OP166D OP166W

935 nm LED Peak Wavelength

Ordering Information

Output Power (mW/cm2) Min / Max

1.95 / NA 1.40 / 2.20 0.85 / 1.60 0.28 / NA 0.50 / NA 1.95 / NA 1.40 / 2.20 0.85 / 1.60 0.28 / NA 0.50 / NA

90°

20 / 50

90°

0.50\"

18°

IF (mA) Total Beam Lead Typ / Max Angle Length

efficiency

• Battery-operated or voltage-limited applications

18°

RoHS

OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.

Issue B 05/2011

Page 1 of 4

OPTEK Technology Inc. — 15 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com

芯天下--http://oneic.com/

Plastic Infrared Emitting Diode OP165, OP166 Series

OP165 (A, B, C, D) OP165W

OP166 (A, B, C, D) DIMENSIONS ARE IN: [MILLIMETERS]INCHES OP166W 1

2

Pin # LED

1 Cathode 2 Anode CONTAINS POLYSULFONE

To avoid stress cracking, we suggest using ND Industries’ Vibra-Tite for thread-locking. Vibra-Tite evaporates fast without causing structural

failure in OPTEK'S molded plastics.

OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.

Issue B 05/2011 Page 2 of 4

OPTEK Technology Inc. — 15 Wallace Drive, Carrollton, Texas 75006

Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com

芯天下--http://oneic.com/

Plastic Infrared Emitting Diode OP165, OP166 Series

Absolute Maximum Ratings (TA=25°C unless otherwise noted)

Storage and Operating Temperature Range Reverse Voltage

Continuous Forward Current

Peak Forward Current (1 µs pulse width, 300 pps)

Lead Soldering Temperature [1/16 inch (1.6 mm) from case for 5 seconds with soldering iron] Power Dissipation

-40o C to +100o C

2.0 V 50 mA 3.0 A 260° C 100 mW(1)

Electrical Characteristics (TA = 25° C unless otherwise noted)

SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS Input Diode EE (APT) PO

Apertured Radiant Incidence

OP165A, OP166A Radiant Power Output OP165W, OP166W

1.95 0.50

- -

- -

mW/cm2 IF = 20 mA(2)

mW IF = 20 mA

VF Forward Voltage IR λP B

Reverse Current

Wavelength at Peak Emission

Spectral Bandwidth between Half Power

Points

Spectral Shift with Temperature OP165, OP166 (A, B, C, D) OP165W, OP166W Emission Angle at Half Power Points OP165, OP166 (A, B, C, D) OP165W, OP166W Output Rise Time Output Fall Time

- - 1.60 V IF = 20 mA - -

- - - - - - -

- 935 50 - ±0.30 18 90 1000 500

100 - - - - - - - -

µA nm nm

VR= 2 V IF = 10 mA IF = 10 mA

∆λP /∆T nm/°C IF = Constant

θHP tr tf

Degree IF = 20 mA ns ns

IF(PK)=100 mA, PW=10 µs, D.C.=10.0% Notes:

1. Derate linearly 1.33 mW/°C above 25°C

2. EE(APT) is a measurement of the average apertured rediant incidence

ipon a sensing area 0.081” (2.06 mm) in diameter, perpendicular to and centered on the mechanical axis of the lens, and 0.590” (14.99 mm) from the measurement surface. EE(APT) is not necessarily uniform within the measured areas.

OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.

OPTEK Technology Inc. — 15 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com

Issue B 05/2011

Page 3 of 4

芯天下--http://oneic.com/

Plastic Infrared Emitting Diode OP165, OP166 Series

OP165, OP166 (A, B, C, D, W)

Forward Voltage vs Forward Current vs Temperature1.81.71.6Typical Forward Voltage (V)1.51.41.31.21.11.00.90510152025303045Forward Current (mA)-65°C-40°C-20°C+0°C+20°C+40°C+60°C+80°C+100°C+125°COptical Power vs IF vs Temp4.0Normalized at 20 mA and 20o C3.53.0-65°C-40°C-20°C+0°C+20°C+40°C+60°C+80°C+100°C+125°CNormalized Optical Power2.52.01.51.00.50.0051015202530304550Forward Current IF (mA)Distance vs Output Power vs Forward Current9Normalized at 0.6\" and 50 mA87Forward Current10 mA20 mA30 mA40 mA50 mA60 mA80 mA100 mARelative Radiant Intensity vs AngularDisplacement1.00.8Normalized Output Power63210Relative Radiant Intensity0.60.40.20.00.0 ''0.2 ''0.4 ''0.6 ''0.8 ''1.0 ''1.2 ''1.4 ''1.6 ''1.8 ''2.0 ''-80-302070Distance (inches)Angular Displacement (Degrees)OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.

Issue B 05/2011 Page 4 of 4

OPTEK Technology Inc. — 15 Wallace Drive, Carrollton, Texas 75006

Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com

芯天下--http://oneic.com/