您好,欢迎来到抵帆知识网。
搜索
您的当前位置:首页7302基本命令

7302基本命令

来源:抵帆知识网
1、 isadmin>configure>system>management# info(查看NT IP) 2、 isadmin>show# system shub entry ip(查看SHUB IP) 3、 isadmin>show# software-mngt oswp detail(查看ISAM VERSION) 4、 isadmin>show# system shub entry version detail(查看SHUB VERSION) 5、 sadmin>show>system>shub# filters shub-manager(查看指向的网管地址)

6、 Isadmin>show# atm pvc(查端口的PVC)

7、 isadmin>show>bridge# network-port detail(查看网络口的状态)

8、 isadmin>show>interface>shub# port(查看网络口的状态)

9、 isadmin>show>vlan# global(查看VLAN的数量)

10、 isadmin>show>vlan# shub-port-vlan-map(查看板卡及网络口对应的VLAN) 11、 isadmin>show>vlan# residential-bridge detail(查所有VLAN对应所带的

端口)

12、 isadmin>show>bridge# port detail

13、 isadmin>show>bridge# shub-info detail(查SHUB MAC)

14、 isadmin>show>vlan# bridge-port-fdb (查看所有VLAN获取端口MAC)

15、 isadmin>show>vlan# fdb (查看某个VLAN获取端口MAC)

16、 isadmin>show>vlan# shub-port-vlan-map(查看所有VLAN所对应的板卡及接

口)

17、 isadmin>show>vlan# shub-filter-entry (查看VLAN所获得的MAC) 18、 isadmin>show>interface>shub#vlan (显示用户VLAN及网络VLAN) 19、 show>bridge#port-to-atm-pvc (显示桥端口与物理端口的对映关系)

1.编写概述

为帮助更好维护7302ISAM设备,编写本文档。本文档所有命令以R2.2为基础,可能因为版本不同而有所变化,具体请参各个版本命令手册。 2.查看命令 2.1 端口部分

1.查看上联端口状态

isadmin># show interface shub port

============================================================ port table

============================================================ port admin-status oper-status speed type duplex -------------------------------------------------------------------------------- 1 down down one-gb unused full 2 down down one-gb unused full

3 down down one-gb unused full 4 up up hundred-mbps network full 5 down down hundred-mbps unused full 6 down down hundred-mbps unused full 7 down down hundred-mbps unused full -------------------------------------------------------------------------------- port count : 7

============================================================ 解释:本命令中,admin-status指上联端口是否激活,up是激活,down是锁定 本命令中,oper-status指上联端口链路是否激活,up是激活,down是不非激活。 本命令中,speed是指上联端口的速率

本命令中,type指端口的类型,主要有:network、subtending、user等,unused表示没有配置任何类型。

本命令中,duplex指端口工作模式,主要有:full、half

2.查看用户端口状态

isadmin># show interface port xdsl-line:1/1/4/1

============================================================ port table

============================================================ port admin-status opr-status

------------------------------------------------------------------------------ xdsl-line:1/1/4/1 admin-up down

------------------------------------------------------------------------------ port count : 1

============================================================

解释:本命令中1/1/4/1 指第4槽位第一个用户端口。7302中第4个槽位是第一块用户板,以次类推,第19个槽位是第16块用户板。第一个槽位是告警板,第二个槽位是NTA板,第三个槽位是NTB板。 本命令中,admin-status的状态指用户端口是否激活,admin-up是激活,admin-down是锁定。 本命令中,opr-status的状态指用户端是否同步,up是同步,down是不同步。

3.查看用户端口Mac地址

isadmin># show vlan bridge-port-fdb

============================================================ bridge-port-fdb table

============================================================ port vlan-id mac status ----------------------------------------------------------------------------- 1/1/4/10:8:35 2692 00:30:1b:27:11:7c learned 1/1/4/11:8:35 2693 4c:00:10:c8:7e:13 learned 1/1/4/38:8:35 2720 00:14:78:c4:f3:4d learned 1/1/4/41:8:35 2723 00:0b:2f:0b:b3: learned

1/1/4/43:8:35 2725 00:33:44:55:67:f0 learned 1/1/4/45:8:35 2727 00:14:78:d3:6e:d7 learned 1/1/6/2:8:35 2780 00:16:ec:bd:1b:74 learned 1/1/6/3:8:35 2781 00:17:31:b5:06:f4 learned 1/1/6/8:8:35 2786 00:a1:b0:02:33:e1 learned 1/1/6/12:8:35 2790 00:0a:eb:df:9b:b1 learned 1/1/6/14:8:35 2792 00:e0:4c:55:95:fc learned 1/1/6/15:8:35 2793 00:14:2a:39:60:4d learned 1/1/6/20:8:35 2798 00:e0:4c:72:5d:34 learned ----------------------------------------------------------------------------- bridge-port-fdb count : 13

============================================================

解释:本命令中1/1/4/10:8:35指用户端口映射的bridge port,vlan-id指用户端口绑定的vlan号,mac指7302学习到的用户PC的Mac地址,该Mac地址只要用户打开PC,Modem同步后即能学习到。

4.查看用户Bridge端口信息 isadmin># show bridge port

================================================================================ port table

================================================================================

port bridge-port pvid default-priority qos-profile status

--------------------------------------------------------------------------------

1/1/4/1:8:35 33 2683 0 00:00:00:00:00:0 0:00:00:00:00:00:00:00:00:00:00:00:00:00 static

1/1/4/2:8:35 34 2684 0 00:00:00:00:00:0 0:00:00:00:00:00:00:00:00:00:00:00:00:00 static

1/1/4/3:8:35 35 2685 0 00:00:00:00:00:0 0:00:00:00:00:00:00:00:00:00:00:00:00:00 static

1/1/4/4:8:35 36 2686 0 00:00:00:00:00:0 0:00:00:00:00:00:00:00:00:00:00:00:00:00 static

1/1/4/5:8:35 37 2687 0 00:00:00:00:00:0 0:00:00:00:00:00:00:00:00:00:00:00:00:00 static

1/1/4/6:8:35 38 2688 0 00:00:00:00:00:0 0:00:00:00:00:00:00:00:00:00:00:00:00:00 static

1/1/4/7:8:35 39 26 0 00:00:00:00:00:0 0:00:00:00:00:00:00:00:00:00:00:00:00:00 static port count : 7

================================================================================

解释:本命令中,bridge-port是7302根据用户端PVC自动映射的,pvid是强制给用户端不

带VLAN信息的帧打上的VLAN Tag标记,default-priority是QoS标记。

2.2 系统部分 1. 查看板卡状态

isadmin># show equipment slot

============================================================ slot table

============================================================ slot actual-type enabled error-status availability ----------------------------------------------------------------------------- 1/1/1 aacu-c yes no-error available 1/1/2 ecnt-a yes no-error available 1/1/3 no no-error not-installed 1/1/4 eblt-a yes no-error available 1/1/5 eblt-a yes no-error available 1/1/6 eblt-a yes no-error available 1/1/7 eblt-a yes no-error available 1/1/8 no no-error not-installed 1/1/9 no no-error not-installed 1/1/10 no no-error not-installed 1/1/11 no no-error not-installed 1/1/12 no no-error not-installed 1/1/13 no no-error not-installed 1/1/14 no no-error not-installed 1/1/15 no no-error not-installed 1/1/16 no no-error not-installed 1/1/17 no no-error not-installed 1/1/18 no no-error not-installed 1/1/19 no no-error not-installed ----------------------------------------------------------------------------- slot count : 19

============================================================

解释:本命令中,slot是板卡槽位,actual-type是板卡类型,enabled是板卡管理状态,正常情况下为yes;error-status是错误状态,正常情况下为no-error,非正常状态有board-missing、board-mismatch等。availability是板卡启用状态,正常情况下为available,非正常状态有init-failure等,板卡刚启动时显示为in-test。

2.查看NT软件版本

isadmin># show software-mngt oswp

============================================================ oswp table

============================================================ index name availability act-status commit-status -------------------------------------------------------------------------------

1 L6GPAA22.418 enabled active committed 2 NO_OSWP empty not-active un-committed ------------------------------------------------------------------------------- oswp count : 2

============================================================ 解释:本命令中act-status为active的为当前在用版本。 3.查看SHUB软件版本

isadmin># show system shub entry version

============================================================ version table

============================================================ sw-ver-name : LANX sw-release-num : 1.0.0.1

hw-ver : H/WVersion1 fw-ver : LANX_R2.2.11.1

============================================================ 解释:本命令中,SHUB软件版本为R2.2.11.1 2.3 告警部分

isadmin># show alarm current table

============================================== table table

============================================== index type last-updated-on ---------------------------------------------- ---------------------------------------------- table count : 0

============================================== 解释:查看当前告警,现用本命令查看告警分类,本例中无告警。一般告警分类有:equipment eqpt-holder、plug-in-unit、atm、ether-itf、sw-mgmt、xdsl、tca-xdsl、eo-conversion、authentication 、bonding-group、redundancy、custom等。

如要看具体告警内容,需要进一步的命令,如: isadmin># show alarm current equipment

============================================================ equipment table

============================================================ index persist-data sntp-comm nt-disk connection-lost ------------------------------------------------------------------------ ------------------------------------------------------------------------ equipment count : 0

============================================================ 3.配置命令

3.1 管理IP地址配置

isadmin># configure system management

isadmin>configure>system>management# info

configure system

#------------------------------------------ echo \"system\"

#------------------------------------------ management

host-ip-address manual:222.184.77.225/24 default-route 222.184.77.1 exit exit

#------------------------------------------ 如要修改IP地址,可以直接修改。

3.2线速模板配置 配置线速模板

isadmin># configure xdsl service-profile 1 name 2M-0K-Fast

isadmin>#configure xdsl service-profile 1 min-bitrate-up min-bitrate-down plan-bitrate-up 0 plan-bitrate-down 2048 max-bitrate-up 0 max-bitrate-down 2048 max-delay-up 1 max-delay-down 1 active 配置协议模板

isadmin># configure xdsl spectrum-profile 1 name adsl isadmin>#configure xdsl spectrum-profile 1 active 默认状态打开如下协议: 协议名称 说明

ansi-t1413 ANSI T1.413-1998 etsi-dts ETSI DTS/TM06006

g992-1-a ADSL G.dmt over POTS g992-1-b ADSL G.dmt over ISDN g992-2-a ADSL G.lite

g992-3-a ADSL2 over POTS g992-3-b ADSL2 over ISDN

注:R2.2版本中如果需要打开ADSL2+等协议需要单独定义 R2.2.03中允许修改Spectrum-Profile

isadmin># configure xdsl spectrum-profile 1 modification start g992-5-a isadmin>configure>xdsl>spectrum-profile>1# modification complete 附: Multi-ADSL Modes of Operation

G.992.1 ADSL G.dmt G.992.2 ADSL G.lite

G.992.3 Annex A ADSL2 operation over POTS non-overlapped spectrum

G.992.3 Annex L READSL2 operation over POTS non-overlapped spectrum US masks G.992.5 Annex A ADSL2+ operation over POTS non-overlapped spectrum

G.992.3 Annex M ADSL2 operation over POTS with extended upstream bandwidth G.992.5 Annex M ADSL2+ operation over POTS with extended upstream bandwidth

登陆帐号:isadmin 登陆密码 ans#150

端口表示方法:1/1/槽号/端口号

1) 查看模板配置命令:

Show>xdsl# info configure xdsl service-profile 2) 查看端口线路模板配置命令:

Show>xdsl# info configure xdsl line 1/1/slot/port 3) 更改端口的模板配置命令:

isadmin>#Configure xdsl line 1/1/slot/port service-profile 1 spectrum-profile 2 admin-up 4) 根据mac查端口

isadmin># Show vlan fdb mac xx:xx:xx:xx:xx:xx 5) 显示所有单板 show equipment slot

6) 查看端口激活情况:

isadmin># show interface port xdsl-line:1/1/4/1 (单个端口)

isadmin># show interface port xdsl-line:1/1/4/[1...48] (查看该板卡所有端口) 端口表示方法:1/1/槽号/端口号

1) 查看模板配置命令:

Show>xdsl# info configure xdsl service-profile 2) 查看端口线路模板配置命令:

Show>xdsl# info configure xdsl line 1/1/slot/port 3)更改端口的模板配置命令:

Configure xdsl line 1/1/slot/port service-profile 1 spectrum-profile 2 admin-up 4根据mac查端口

Show vlan fdb mac xx:xx:xx:xx:xx:xx

显示所有单板:show equipment slot

查看端口激活情况:show atm pvc 1/1/槽号/端口号:0:35 注:当要查看多个端口或槽位时,可用[x…y]表示范围

打死激活端口

lock端口和unlock端口

1.configure xdsl line 1/1/4/1 no admin-up 2.configure xdsl line 1/1/4/1 admin-up

查看设备配置的速率模板及对应的index号:

isadmin># info configure xdsl service-profile

查看当前某个端口具体的配置的速率:

isadmin># info configure xdsl line 1/1/4/1

批量修改端口速率

configure xdsl line 1/1/4/[1...48] service-profile 3 spectrum-profile 1 admin-up

查看当前具体某个端口的状态

isadmin># show interface port xdsl-line:1/1/4/27

====================================================================== port table

====================================================================== port admin-status opr-status

-------------------------------------------------------------------------------- xdsl-line:1/1/4/27 admin-up down

-------------------------------------------------------------------------------- port count : 1

======================================================================

因篇幅问题不能全部显示,请点此查看更多更全内容

Copyright © 2019- dfix.cn 版权所有 湘ICP备2024080961号-1

违法及侵权请联系:TEL:199 1889 7713 E-MAIL:2724546146@qq.com

本站由北京市万商天勤律师事务所王兴未律师提供法律服务